CARVIN
Sign in
Moderate⏱ 2 - 4 h15 steps·Original on iFixit ↗

Replace the Front Brake Pads and Rotors on Your 2018‑2024 Jeep Wrangler JL

This guide shows how to remove and replace worn out brake pads and brake rotors on a 2018–2024 Jeep Wrangler (JL).

Worn front pads or warped rotors reduce stopping power, create vibration, and can damage other brake components on your Wrangler JL. Replacing the pads, rotors, and slide clips restores factory braking performance and prevents costly repairs.

Follow this guide to swap in new Mopar‑style components with basic hand tools in your driveway or garage.

Tools (19)

Parts (3)

  • 2× Front Brake Pads: 2018–2024 Jeep Wrangler JL buy ↗
  • 2× Front Brake Rotor: 2018–2024 Jeep Wrangler JL buy ↗
  • 2× Caliper Hardware buy ↗

Step-by-step instructions

1

Secure the Jeep and prepare the workspace

  • [youtubetimestamp|51|120]Break loose the wheel lug nuts for the brake you need to work on.
  • [youtubetimestamp|51|120]Raise the Jeep using a floor jack and support it securely on jack stands.
  • [youtubetimestamp|51|120]Refer to your owner's manual for safe jacking locations.
  • [youtubetimestamp|51|120]Remove the lug nuts and the wheel.
  • [youtubetimestamp|51|120]Position an oil pan beneath the hubs to catch brake cleaner and debris.
  • [youtubetimestamp|51|120]Put on chemical‑resistant gloves and safety glasses before using cleaners or lubricants.
2

Clean the brake components

  • [youtubetimestamp|124|132]Spray the caliper, rotor and surrounding hardware with brake cleaner to remove built‑up dust.
  • [youtubetimestamp|124|132]Scrub remaining grime with a wire brush until the metal surfaces are clean.
  • [youtubetimestamp|124|132]Let excess cleaner drain into the pan before proceeding.
3

Depress the caliper pistons

  • [youtubetimestamp|147|165]Unscrew the master cylinder reservoir cap and set it aside.
  • [youtubetimestamp|147|165]Place a large c‑clamp over the caliper and old pads and tighten until both pistons fully retract.
  • [youtubetimestamp|147|165]Fluid may rise in the reservoir, so protect painted surfaces from spills.
4

Remove the caliper

  • [youtubetimestamp|165|176]Remove the two 13 mm slide pin bolts with a ratchet or wrench.
  • Lift the caliper off the bracket and suspend it with a caliper hanger to avoid hose strain.
5

Remove the pads and hardware

  • [youtubetimestamp|176|186]Pull the inner and outer brake pads straight out of the mounting bracket.
  • [youtubetimestamp|176|186]Pry out and discard the four pad slide clips.
  • [youtubetimestamp|176|186]If you were only replacing pads, new clips and pads could be installed now.
6

Detach the caliper mounting bracket

  • [youtubetimestamp|186.8|207.7]Break loose the two caliper bracket bolts with a 21 mm socket and long handle wrench or impact gun.
  • [youtubetimestamp|186.8|207.7]Expect the bolts to be very tight because the bracket withstands braking forces.
  • [youtubetimestamp|186.8|207.7]Remove the bolts and slide the bracket off the knuckle.
7

Remove the rotor

  • [youtubetimestamp|219.3|244.1]Insert a T30 Torx bit into the rotor retaining screw and break it free with a socket wrench.
  • Remove the screw and pull the rotor off the hub, using a pry tool for leverage if needed.
  • Brush any rust off the hub face with a wire brush.
8

Install the new rotor

  • [youtubetimestamp|298.5|318.6]Slide the new rotor onto the hub and align the screw hole.
  • [youtubetimestamp|298.5|318.6]Coat the retaining screw threads with anti‑seize and torque the T30 screw to ***15 ft‑lbs***.
  • [youtubetimestamp|298.5|318.6]Spray both rotor faces with brake clean and wipe them with a shop towel to remove the factory coating.
9

Reattach the caliper bracket

  • [youtubetimestamp|319.2|331.4]Position the caliper mounting bracket over the rotor and hand‑thread the two 21 mm bolts.
  • [youtubetimestamp|319.2|331.4]Torque each bracket bolt to ***148 ft‑lbs***.
10

Fit new pad slide clips

  • [youtubetimestamp|331.4|338.9]Press the four new slide clips into the bracket so their return springs face away from the rotor.
11

Install the brake pads

  • [youtubetimestamp|339.8|358.7]Spread a thin layer of caliper lubricant on both metal ears of each brake pad.
  • [youtubetimestamp|339.8|358.7]Slide the inner and outer pads into the bracket until the return springs pull them slightly away from the rotor.
  • [youtubetimestamp|339.8|358.7]Verify the pads move freely without binding.
12

Lubricate slide pins and caliper surfaces

  • [youtubetimestamp|359|381]Pull each slide pin from the caliper, remove the boot, and wipe off any old grease.
  • [youtubetimestamp|359|381]Apply fresh caliper lubricant to the pin and reinstall the boot.
  • [youtubetimestamp|359|381]Spread a light coat of lubricant on the inner caliper surface and piston face.
13

Reinstall the caliper

  • [youtubetimestamp|381.1|395.2]Lower the caliper over the new pads and align the slide pins with their holes.
  • [youtubetimestamp|381.1|395.2]Install the two 13 mm bolts and torque them to ***27 ft‑lbs***.
14

Repeat on the passenger side

  • [youtubetimestamp|395.2|405.7]Repeat the removal and installation process on the passenger‑side front brake assembly.
15

Finalize and test the system

  • [youtubetimestamp|405.7|417.7]Reinstall the master cylinder reservoir cap securely.
  • [youtubetimestamp|405.7|417.7]Pump the brake pedal several times until it feels firm to seat the pistons.
  • [youtubetimestamp|405.7|417.7]Don't drive your Jeep until the pedal feels solid and responsive.

Conclusion

With both front corners finished and the brake pedal pumped firm, reinstall the wheels, lower the Jeep, and enjoy restored, confident braking on your Wrangler JL.

Replacements didn't go as planned? Ask our Jeep Wrangler JL Answers Community for help.

Guide content belongs to iFixit, license CC BY-NC-SA. Open original

Замените передние тормозные колодки и диски на Jeep Wrangler JL 2018–2024 годов. — Carvin Garage · Carvin